An induction cooktop is normally hardwired on its own dedicated circuit, sized to the rating in the install manual, and connected by a licensed electrician. The two things that decide how big the job is are whether there’s already a suitable cooktop circuit, and if your switchboard and power supply have the capacity. Swapping from an old electric cooktop is usually simpler than swapping from gas.
Why does an induction cooktop need its own circuit?
Induction cooktops can draw a large current when several zones are on high or a boost setting is running. A dedicated circuit means that load has its own cable and its own protection at the switchboard, sized for it. Sharing a circuit with power points or other appliances would mean nuisance tripping at best and overheated cable at worst.
The install manual lists the circuit rating the cooktop needs. Some models can be set at install to a lower maximum to suit a smaller circuit, at the cost of a bit of boost power. We check that before quoting.
I’m swapping from an electric cooktop. Is it straightforward?
Often, yes. There’s already a dedicated circuit to the cooktop. The question is whether it’s rated high enough for the new unit, and whether the cable is in good shape. Old ceramic and coil cooktops often ran on a smaller circuit than a modern induction unit wants. If the rating is short, the cable and circuit breaker may need upgrading.
The cut-out in the bench matters too. Induction cooktops come in standard widths, but the cut-out size varies by brand. If the new unit doesn’t match, the benchtop needs cutting or a filler, which is a job for your stone mason or cabinet maker, not the electrician.
I’m swapping from gas. What’s involved?
More work, because there’s usually no high-rated circuit in the kitchen for cooking. That means:
- A new circuit and cable from the switchboard to the cooktop.
- Room on the switchboard for a new circuit breaker and safety switch protection.
- A check that your total load and supply can carry it.
- A licensed gas fitter to cap off the gas line. That’s separate from the electrical work.
Plan the electrical side first so the gas fitter and electrician aren’t waiting on each other.
Will my switchboard need an upgrade?
It might. Older boards with ceramic fuses, no spare space or no safety switches can’t take a new high-current circuit cleanly. In Queensland, when circuits are added, safety switch protection is required. The Electrical Safety Office also recommends safety switches on every circuit, including the cooktop. A full board is one of the most common reasons an induction swap turns into a switchboard upgrade.
Does the power supply to the house matter?
On most homes, no. But if you’re already running ducted air, an electric hot water system, a pool pump and maybe an EV charger, adding a big cooktop all on a single phase can push the total demand up. Your electrician should look at what’s already on the supply before adding a large load.
Can I install an induction cooktop myself?
No. Hardwired cooktops must be connected by a licensed electrician in Queensland. The Electrical Safety Office says buying hardwired appliances isn’t illegal, but connecting them is licensed work. DIY electrical work is illegal and can void an insurance claim. Many makers also require licensed installation in their warranty terms.
Fins Up Electrical installs and connects induction cooktops across the Redcliffe peninsula and Moreton Bay. Send us the model and a photo of your switchboard and we will tell you what’s involved, with a free fixed quote before any work starts. Licence 91921. See oven and cooktop installation.
Want this sorted? Oven and cooktop installation from Fins Up.
Licensed electrician, licence 91921. Free quote before any work starts. Open 24 hours Monday to Saturday.
Common questions
Can an induction cooktop plug into a normal power point?
Full-size induction cooktops are hardwired on their own circuit. Some small portable single-zone units plug in, but they’re a different product.
Do I need a new circuit to replace a ceramic cooktop with induction?
Not always. If the existing cooktop circuit is rated for the new unit and the cable is sound, it can be reused.
Who caps the gas when I switch to induction?
A licensed gas fitter. The electrician handles the new circuit and the connection.