Blog

How to get power to a shed

· 3 min read · Fins Up Electrical, licence 91921

5.0 on GoogleLicence 91921Open 24 hours, Mon to SatFree quotes

The usual way to get power to a shed is a cable run from your house switchboard, either underground or overhead, feeding power points and lights in the shed. A shed with a lot of load, like a workshop, often gets its own small switchboard. In Queensland, the wiring and connection must be done by a licensed electrician. Running an extension lead out to the shed is not a fix.

What are the options for powering a shed?

  • Underground cable from the house. The most common. A cable in conduit runs from the switchboard, under the yard, into the shed. Neat and out of the way.
  • Overhead cable. Strung from the house to the shed on a catenary wire. Used where digging isn’t practical, but it has height and clearance rules and is less common on suburban blocks.
  • Off the house wall. For a shed or carport built against the house, cable can often run through the roof or along the wall.
  • Solar with a battery. A standalone setup can run lights and a phone charger in a remote shed. It won’t run a welder or a fridge reliably.

What decides how big the job is?

What you’ll run in the shed. A couple of lights and a power point for a battery charger needs much less than a workshop with a compressor, a drop saw, a beer fridge and air conditioning. The load sets the cable size, and so does the distance from the house. Longer runs need heavier cable to stop the voltage dropping too far.

Tell your electrician everything you might plug in, including what you’ll add later. Running a bigger cable now costs much less than digging the trench twice.

Does a shed need its own switchboard?

A small shed with lights and a point or two can often run off one circuit from the house. A bigger shed or workshop with several circuits usually gets a sub-board in the shed, fed from the main board. That gives you local circuit breakers and safety switches, so a tripped saw doesn’t mean walking back to the house in the dark. In Queensland, power point and lighting circuits added to a home need safety switch protection, and that includes the shed.

Can I dig the trench and lay the cable myself?

Installing the cable, connecting it and wiring the shed are electrical work, and only a licensed electrician can do them in Queensland. The Electrical Safety Office is clear that DIY electrical work is illegal, carries large fines, and can void an insurance claim. Underground cable also has to meet the wiring rules for depth, conduit and marking, and your electrician has to test the whole installation before it goes live.

If you want to help with digging to save time, talk to the electrician first. They’ll tell you where it goes and what it needs. Before anyone digs, check for buried services through Before You Dig Australia. Hitting an underground cable or gas line is dangerous.

Why not run an extension lead out to the shed?

Because leads aren’t built to live outside permanently. They get run over by the mower, chewed, left in puddles and cooked in the sun. A lead feeding power boards in a shed full of tools is a common source of overheating and shocks. If the lead is the shed’s only power, it’s time to wire it properly.

What about lights on the way to the shed?

While the trench is open, it’s worth adding path or garden lights, or a sensor light on the shed. Fins Up Electrical has wired sheds and fitted driveway and outdoor lights around Moreton Bay. We will look at the shed, the run and your switchboard, then give you a free fixed quote before any work starts. Licence 91921. See shed, garage and outdoor power. If the main board needs room for the new circuit, see switchboard upgrades.

Want this sorted? Shed and outdoor power from Fins Up.

Licensed electrician, licence 91921. Free quote before any work starts. Open 24 hours Monday to Saturday.

Common questions

Do I need an electrician to put power in my shed?

Yes. In Queensland, running the cable, connecting it and wiring the shed is electrical work that must be done by a licensed electrician.

Does shed power need a safety switch?

Yes. Power point and lighting circuits added to a home in Queensland need safety switch protection, and a shed is no different.

Can I run my shed off solar instead?

A small standalone solar and battery setup can run lights and light loads. For tools, fridges or air conditioning, a cable from the house is more reliable.

Sources

The service