Blog

Power point not working? Here’s what to check

· 3 min read · Fins Up Electrical, licence 91921

5.0 on GoogleLicence 91921Open 24 hours, Mon to SatFree quotes

When a power point stops working, start with the simple stuff: test it with a different appliance, check the switch on the point, and look at the switchboard for a tripped safety switch or circuit breaker. If those check out and it’s still dead, there’s likely a loose connection or a failed outlet, and that’s a job for a licensed electrician.

What should I check first?

  1. Try a different appliance. A lamp or phone charger you know works. Plenty of dead power points turn out to be a dead appliance.
  2. Check the switch on the point is on. Obvious, but easy to miss behind furniture.
  3. Check other points in the room. If several are dead, it’s a circuit problem, not one outlet.
  4. Look at the switchboard. Find any safety switch or circuit breaker in the off position. Safety switches have a 'T' or 'Test' button.

What if something has tripped at the switchboard?

Unplug everything on that circuit and reset the switch. If it holds, plug things back in one at a time. That’s the method Queensland’s Electrical Safety Office recommends for finding a faulty appliance.

If the switch trips again with everything unplugged, or won’t reset at all, the Electrical Safety Office says that may mean a fault on the circuit that needs a licensed electrician. Leave it off and call one.

What if nothing has tripped?

Then the fault is usually at or near that point:

  • A loose connection behind the plate or at the previous point on the circuit. Power points are wired in a chain, so a loose connection at one can kill the ones after it.
  • A failed outlet. The switch or contacts inside wear out, especially on points that get used hard, like the kettle point.
  • A damaged cable in the wall, often after a renovation or hanging something heavy.
  • A USB point that’s failed on the USB side but still works for plugs, or the other way round.

All of these mean opening the point or the wiring, and that’s electrical work. In Queensland only a licensed electrician can do it.

When is a dead power point a safety issue?

A point that’s simply dead isn’t usually urgent. Treat it as urgent if:

  • there’s a burning or fishy smell, or scorch marks on the plate
  • it buzzes or crackles
  • it stopped working with a bang or a flash
  • the plate feels warm with nothing plugged in

Those point to a connection that’s overheated. Switch that circuit off at the switchboard if you can do it safely, and call an electrician.

Why does it work sometimes and not other times?

A point that cuts in and out is a bigger worry than one that’s simply dead. It usually means a loose connection that makes contact some of the time. Every time it makes and breaks, it arcs and heats up. Wiggling the plug to get it going again is a sign to stop using it.

The same goes for a plug that falls out of the point or feels loose. The contacts inside have lost their grip, which makes heat. Leave it switched off and get it looked at.

How do we fix it?

We test the dead point and the others on the circuit, find where the supply stops, and fix the connection or replace the outlet. If you’re using power boards because you’re short on outlets, it’s a good time to add points where you need them. We fit standard double points, USB points and weatherproof outdoor points.

Fins Up Electrical covers Scarborough, Redcliffe, North Lakes and the rest of Moreton Bay, 24 hours Monday to Saturday. The quote is free and comes before any work starts. For a bigger fault on the circuit, see our repairs and fault finding service.

Want this sorted? Power point installation from Fins Up.

Licensed electrician, licence 91921. Free quote before any work starts. Open 24 hours Monday to Saturday.

Common questions

Why did half my power points stop working?

Usually a safety switch or circuit breaker has tripped, or a loose connection at one point has cut supply to the points wired after it.

Can a power point just wear out?

Yes. The contacts and switch inside wear with use, and heavily used points like the kettle or heater point fail first.

Can I change a power point myself?

No. Replacing a power point is electrical work and in Queensland it must be done by a licensed electrician. It’s illegal to do it yourself.

Sources