When the hot water keeps tripping the safety switch, the most common cause is a failing heating element. Water gets into the element as it wears out and current leaks to earth, often when the system switches on overnight. A damaged cable or a faulty thermostat can do the same. The system is hard-wired, so this is a job for a licensed electrician, not something to reset over and over.
Why is it nearly always the element?
An electric hot water system heats water with an element sitting inside the tank. Over years the element’s outer sheath corrodes and cracks. Once water gets in, current leaks from the element to the tank, and the safety switch sees that leak and cuts the power.
Because many hot water systems run on an off-peak tariff that heats overnight, the trip often happens while you’re asleep. You wake up to no hot water and a tripped switch.
What else can cause it?
- The thermostat. A faulty thermostat can leak or short.
- The cable to the unit. Outdoor units on Redcliffe peninsula homes cop a lot of weather, and the cable and its entry point can break down.
- Water inside the cover. A leaking valve or a damaged cover can let water drip onto the terminals.
- A shared circuit. If the hot water shares a safety switch with other gear, the fault might not be the hot water at all.
What can I check without opening anything?
Plenty, as long as you leave the covers on:
- Check which switch tripped. Is it labelled hot water, or is it a shared one?
- Note when it trips. Overnight points strongly at the heating cycle.
- Look at the tank from the outside. Is there water pooling at the base, or rust streaks running down the cover?
- Check if there’s water dripping from the relief valve more than usual.
Don’t take the element cover off. Behind it are live terminals at full mains voltage, and isolating or testing a hard-wired hot water system is electrical work. In Queensland that has to be done by a licensed electrician.
Can I leave the safety switch off for now?
Yes. Leaving it off is the safe choice until it’s fixed. If the hot water is on its own circuit, you’ll lose hot water but the rest of the house is fine. If it shares a safety switch with power points or lights, you may lose more than that, which is a good reason to get it seen quickly.
What you shouldn’t do is keep resetting it. The Electrical Safety Office says a safety switch that won’t reset may mean a fault on the circuit that needs a licensed electrician to inspect and repair.
Does a tripping hot water system mean I need a new one?
Not always. Replacing an element or thermostat is often enough when the tank itself is sound. If the tank is leaking or badly rusted, the element is the least of its worries. We’ll test the element and wiring, tell you which it is, and quote the fix before doing it.
Who fixes it on the peninsula?
Fins Up Electrical tests and repairs hot water electrical faults as part of our repairs and fault finding service. We’re based in Scarborough and cover up to 60km, so Redcliffe, Kippa-Ring, North Lakes and out to Caboolture. Open 24 hours Monday to Saturday, licence 91921, free quote before any work starts.
If your board only has one or two safety switches and the hot water keeps taking other circuits down with it, ask us about a switchboard upgrade so each circuit has its own protection.
Want this sorted? Electrical repairs from Fins Up.
Licensed electrician, licence 91921. Free quote before any work starts. Open 24 hours Monday to Saturday.
Common questions
Why does the hot water trip the safety switch at night?
Many systems heat overnight on an off-peak tariff. When the element switches on, a leaking element trips the safety switch.
Can I replace a hot water element myself?
No. It’s hard-wired electrical work, and in Queensland it must be done by a licensed electrician. It’s dangerous and illegal to do it yourself.
Should the hot water system have its own safety switch?
The Electrical Safety Office recommends safety switches on all circuits, including hot water. Separate protection also means a hot water fault does not knock out other circuits.
How long can I go without hot water while it is sorted?
Leave the switch off until it is checked. We are open 24 hours Monday to Saturday, so you can call it in when it happens instead of waiting for a weekday.