Blog

What is electrical fault finding?

· 3 min read · Fins Up Electrical, licence 91921

5.0 on GoogleLicence 91921Open 24 hours, Mon to SatFree quotes

Electrical fault finding is the process a licensed electrician uses to track down why something in your electrical system isn’t working properly, like a safety switch that keeps tripping, a dead circuit or lights that flicker. It means testing the circuit with proper instruments, splitting it into sections and narrowing it down until the faulty cable, fitting or appliance is found. Once the fault is found, the fix is usually the quick part.

When do you need fault finding?

Any time the symptom doesn’t tell you the cause. Common ones:

  • a safety switch that trips, especially with nothing plugged in
  • a circuit breaker that won’t stay on
  • power points or lights that are dead with nothing tripped
  • flickering or dimming that comes and goes
  • tripping that only happens at night or when it rains
  • a tingle from a tap or appliance (call Energex on 13 19 62 first for that one)

If the problem is obvious, like a scorched power point, that’s a repair, not fault finding. Fault finding is for when the cause is hidden somewhere in the walls, roof or switchboard.

What can I do before the electrician arrives?

A few checks save real time and are safe for anyone:

  • Note which switch tripped and what it’s labelled.
  • Unplug the appliances on that circuit, reset, and plug them back in one at a time. That’s the Electrical Safety Office’s method for finding a faulty appliance.
  • Write down when it happens: time of day, weather, what was running.
  • Note anything you’ve seen or smelt, like buzzing, burning or a flash.

Leave the rest to the electrician. Opening fittings, testing circuits and working at the switchboard is electrical work, and in Queensland it has to be done by a licensed electrician.

What does an electrician do during fault finding?

  1. Listen to the story. When it started, what trips, what was running. This often points straight at a likely area.
  2. Isolate the circuit. The faulty circuit is switched off and made safe to work on.
  3. Test it. An insulation resistance tester shows if current is leaking to earth somewhere on the circuit, even if nothing is tripping right now. Other tests check continuity and connections.
  4. Split it up. The circuit is broken into sections at points and junctions, and each section is tested until the fault is pinned to one run of cable or one fitting.
  5. Confirm it. Once the faulty part is out of the circuit, the rest should test clean.

Why can some faults take longer to find?

Some faults are solid and show up on the first test. Others only appear when it’s wet, hot or when a particular appliance switches on. Those intermittent faults can take more testing. Long circuits in big homes, ceiling spaces that are hard to get into, and wiring that’s been extended over the years without good records all add time.

That’s why the notes you take help. "Only trips after rain" sends us straight to outdoor gear instead of testing every point in the house.

What happens once the fault is found?

We tell you what we found, show you if you want to see it, and quote the repair before doing it. Common fixes are replacing a water-damaged outdoor fitting, a failed hot water element, a scorched power point or a length of damaged cable. If the board itself is part of the problem, we’ll explain your switchboard upgrade options.

Fins Up Electrical does fault finding and repairs across the Redcliffe peninsula and Moreton Bay. Andrew has 16 years on the tools and holds electrical contractor licence 91921. We’re open 24 hours Monday to Saturday.

Want this sorted? Electrical repairs from Fins Up.

Licensed electrician, licence 91921. Free quote before any work starts. Open 24 hours Monday to Saturday.

Common questions

Is fault finding the same as a repair?

No. Fault finding is working out what’s wrong. The repair is fixing it. On simple jobs they happen in the same visit.

Can a fault be found if nothing is tripping right now?

Often, yes. Insulation testing can show a leak to earth on a circuit even when the safety switch is holding.

Can I do my own fault finding with a multimeter?

No. Testing circuits is electrical work, and in Queensland it must be done by a licensed electrician. You can safely unplug appliances and reset the switch, and that’s it.

Sources

The service